Grade 11 · CAPS · English

Grade 11 Engineering Graphics and Design Study Guide

Complete Grade 11 Engineering Graphics and Design study guide in English, aligned to the CAPS curriculum. 16 chapters with explanations, worked examples, exercises with solutions, and original practice papers with memos.

16Chapters
217Practice Qs & solutions
2Practice papers (short + full)
∞Lifetime access
Unlock this subject Start reading See practice papers

Chapters

Chapter 1. Drawing Equipment, Line Types and Caption Standards FREE

When the engineers at Murray and Roberts prepared the working drawings for the Gautrain viaducts, every single sheet had to speak the same visual language so that a draughtsperson in Centurion and a steel fabricator in Vereeniging would read it identically. A drawing that costs R2 000 to produce but is misread can cause a column to be cast 50 mm too short, wasting tens of thousands of rands in rework. This is why Engineering Graphics and Design begins with the boring-sounding but absolutely critical foundations: the equipment you draw with, the standardised line types that carry meaning, and the caption standards (the title block, borders and lettering) that make a drawing a legal, traceable document. In South Africa these conventions are set by SANS 10111, which is closely aligned with the international ISO standards.

1.1 Drawing equipment and its correct use

A Grade 11 learner must know each instrument by name and know what it does. The drawing board provides a flat, true reference edge. A T-square or a parallel rule slides along that edge to draw horizontal lines. Two set squares (the 45 degree and the 30/60 degree triangles) ride on the T-square to give vertical lines and standard angles; combining them gives angles in 15 degree steps (such as 75 degrees from 45 plus 30).

Other essential items include a pair of compasses for circles and arcs, a divider for transferring measurements, a protractor for measuring angles, and a French curve for fairing irregular curves. Pencils are graded by hardness: a 2H pencil gives thin, light construction lines, while an HB or B gives the dark, thick outlines. Good practice is to keep the pencil sharp and to rotate it while drawing so the line stays an even width.

Example: To draw a line at 75 degrees to the horizontal without a protractor, you stack the two set squares. Step 1: rest the 30/60 triangle on the T-square. Step 2: place the 45 triangle against the sloped edge of the first. Step 3: the resulting edge sits at \(30^\circ + 45^\circ = 75^\circ\) to the horizontal. Draw along that edge.

1.2 Line types and their meanings

Every line on an engineering drawing has a defined type (continuous, dashed or chain) and a defined thickness (thick or thin), and each combination has a fixed meaning. The reader must never have to guess. The two standard widths used at school level are roughly 0,7 mm for thick lines and 0,35 mm for thin lines, a ratio of about \(2:1\).

  • Thick continuous line: visible outlines and visible edges of an object.
  • Thin continuous line: dimension lines, projection (extension) lines, hatching for sections and leader lines.
  • Thin dashed line: hidden detail (edges and outlines you cannot see from that view).
  • Thin chain line (long dash, short dash): centre lines of circles and holes, and axes of symmetry.
  • Thick chain line: indicates a surface that must receive special treatment, such as hardening.
  • Thin chain line thickened at the ends and at changes of direction: a cutting plane, showing where an imaginary cut is made for a sectional view.
  • Thin continuous wavy (freehand) line or a thin ruled zig-zag line: a short break or a long break, used to shorten a long uniform part on the sheet.

1.3 Caption standards: borders, title block and lettering

The caption of a drawing is everything that frames and identifies it. A standard A3 or A4 sheet carries a printed border set in from the paper edge, with a wider margin (about 20 mm) on the left so the sheet can be filed or bound. In the bottom right-hand corner sits the title block, which records the drawing title, the drawing number, the scale, the projection symbol (first-angle or third-angle), the name of the person who drew it, the date, and the units. Because this block makes the drawing traceable, it functions as the document control panel of the sheet.

Lettering must be done in a single, consistent, upright style so it cannot be misread. CAPS expects neat capital letters and numerals of an even height, usually about 3 mm to 5 mm tall, with consistent spacing. Sloppy or decorative lettering loses marks because it can be ambiguous on a working site.

Example: A learner is told a casting bracket is 600 mm long but the A4 sheet is only 297 mm wide. They choose a scale of \(1:2\), so the drawn length is \(\frac{600}{2} = 300\) mm. Because this still slightly exceeds the usable width, they move to \(1:5\), giving \(\frac{600}{5} = 120\) mm, which fits comfortably. The chosen scale 1:5 must then be written in the title block so that anyone reading the sheet knows the true size.

1.4 Paper sizes and the ISO A-series

South African drawing sheets follow the ISO A-series. Each size is exactly half of the one above it: an A3 sheet folded in half gives two A4 sheets. The aspect ratio of every sheet is \(1 : \sqrt{2}\), which is what keeps the proportions constant when you halve the sheet. Knowing the series matters because the title block, border widths and lettering height are all chosen to suit the sheet size, and an examiner expects a Grade 11 candidate to set out a sheet correctly before a single object is drawn.

Chapter 2. Freehand Sketching of Single Objects in Isometric and Oblique

You will see the full content once you unlock this subject. Unlock for R99.

Chapter 3. Freehand Pictorial Sketching of Assemblies and Sectioned Parts

You will see the full content once you unlock this subject. Unlock for R99.

Chapter 4. Instrument Drawing Conventions, Scales and Dimensioning Rules

You will see the full content once you unlock this subject. Unlock for R99.

Chapter 5. Geometrical Constructions, Polygons and Tangency

You will see the full content once you unlock this subject. Unlock for R99.

Chapter 6. Loci of Mechanisms and Helices

You will see the full content once you unlock this subject. Unlock for R99.

Chapter 7. Interpenetration of Prisms, Cylinders and Cones

You will see the full content once you unlock this subject. Unlock for R99.

Chapter 8. Development of Surfaces of Geometric Solids

You will see the full content once you unlock this subject. Unlock for R99.

Chapter 9. First and Third Angle Orthographic Projection in Two Dimensions

You will see the full content once you unlock this subject. Unlock for R99.

Chapter 10. Sectional Orthographic Views and Conventions

You will see the full content once you unlock this subject. Unlock for R99.

Chapter 11. Isometric Drawing of Components from Orthographic Views

You will see the full content once you unlock this subject. Unlock for R99.

Chapter 12. Civil Drawing: Floor Plans, Elevations and Site Conventions

You will see the full content once you unlock this subject. Unlock for R99.

Chapter 13. Mechanical Detail Drawing of Single Components

You will see the full content once you unlock this subject. Unlock for R99.

Chapter 14. Fasteners, Screw Threads and Machine Conventions

You will see the full content once you unlock this subject. Unlock for R99.

Chapter 15. Mechanical Assembly Drawing and Parts Lists

You will see the full content once you unlock this subject. Unlock for R99.

Chapter 16. Analysing Assemblies: Disassembly, Function and Interpretation

You will see the full content once you unlock this subject. Unlock for R99.

Practice papers

Grade 11 Engineering Graphics and Design - Term 2 Paper (Q2 Short) 30 marks · 60 min
Grade 11 Engineering Graphics and Design - Term 2 Examination (Paper 2: Full) 60 marks · 120 min
Grade 11 Engineering Graphics and Design - Paper 4 (Short) 30 marks · 60 min
Grade 11 Engineering Graphics and Design - Paper 4 (Term 4) 60 marks · 120 min
Term 2 Exam: Advanced 50 marks · 90 min
Term 4 Exam: Advanced 49 marks · 90 min
Grade 11 Engineering Graphics and Design: Term 3 Test 50 marks · 60 min

Sample questions from this subject

  1. Which pencil grade is most suitable for thin, light construction lines?
  2. What does a thin dashed line represent on an engineering drawing?
  3. In the bottom right-hand corner of a standard drawing sheet you will find the:
  4. Which South African standard governs drawing conventions for EGD?

Unlock the subject for the full questions, memos and step-by-step solutions.

About this study guide

This Grade 11 Engineering Graphics and Design study guide is written in clear English, following the CAPS curriculum for South African schools. Each chapter starts with the core content, shows worked examples, and ends with exercises whose solutions are already in the guide.